rev b dtem 1024 series 16~36 watts medical ac/dc desktop power supplies 09/22 /201 4 wall industries, inc. ? 37 industrial drive, exeter, nh 03833 ? tel: 603 - 778 - 2300 ? toll free: 888 - 597 - 9255 ? fax 603 - 778 - 9797 website: www.wallindustries.com ? e - mail: sales@wallindustries.com page 1 of 3 iec - 320 - c14 iec - 320 - c8 iec - 320 - c6 iec - 320 - c18 size: 3.94 x 1.77 x 1.22 inches size: 3.94 x 1.77 x 1.22 inches size: 3.94 x 1.77 x 1.22 inches size: 3.94 x 1.77 x 1.22 inches features ? single outputs ? rohs & weee compliance ? efficiency meets cec level v, vi ? short circuit & over voltage protection x iec - 320- c14, iec - 320 - c8, iec - 320- c6, & iec - 320- c18 ac inlets available ? ul/cul 60601: 3rd edition medical appr ovals ? tuv/sud en/iec 606001 approvals for class ii x 100~240vac input voltage range ? mtbf > 30,000 hours ? optional output connectors available ? cb, ce, fcc approvals description the dtem 1024 series of medical ac/dc desktop power supplies provides up to 36 watts of continuous output power in a 3.94? x 1.77? x 1.22? packag e. all models have a single output and a wide input voltage range of 100~240vac. this series is rohs and weee compliant and m eets cec level v, vi requirements. this series also has ul/cul 60601 and tuv /sud en/iec 60601 3rd edition (for class ii) medical a pprovals. all models are protected against short circuit and over voltage conditions. four ac inlet connector types are available for this series: iec - 320- c14, iec - 320 - c8, iec - 320 - c6, and iec - 320 - c18. optional output connectors are also available please ca ll factory for ordering details. model selection table model number (1) input voltage range output voltage (2) output current load regulation line regulation (3) ripple & noise (4 ) output power min max dte m 1024a x 100 ~ 240 vac 5 ~ 8 vdc 0a 2.0 a 5% 1% 10 0mvp - p 16 w dtem 1024b x 5 ~ 8 vdc 0a 3.0 a 5% 1% 10 0mvp - p 20 w dtem 1024c x 5 ~ 8 vdc 0a 4.0 a 5% 1% 10 0mvp - p 24 w dtem 1024d x 9 ~ 1 1 vdc 0a 1.5 a 5% 1% 25 0mvp - p 18 w dtem 1024e x 9 ~ 1 1 vdc 0a 2.0 a 5% 1% 25 0mvp- p 24 w dtem 1024f x 9 ~ 1 1 vdc 0 a 3.0 a 5% 1% 25 0mvp - p 27 w dtem 1024g x 12 ~ 1 7 vdc 0a 1.66 a 5% 1% 25 0mvp - p 20 w dtem 1024h x 12 ~ 1 7 vdc 0a 2.5 a 5% 1% 25 0mvp - p 30 w dtem 1024j x 18 ~ 24 vdc 0a 1.33 a 5% 1% 35 0mvp - p 24 w dtem 1024k x 18 ~ 24 vdc 0a 1.66 a 5% 1% 35 0mvp - p 3 0w dtem 1024 m x 36 ~ 48 vdc 0a 0.55 a 5% 1% 48 0mvp - p 2 0w dtem 1024n x 36 ~ 48 vdc 0a 0.83a 5% 1% 48 0mvp - p 30w dtem 1024p x 12v 0a 3.0a 5% 1% 25 0mvp - p 36w dtem 1024q x 12v 0a 2.0a 5% 1% 25 0mvp - p 24w dtem 1024r x 24v 0a 1.5a 5% 1% 350mvp - p 36w notes 1. the ? x ? in the model number represents the type of ac inlet connector: ? x ? can be ? 1 ? for iec - 320 - c14 type, ? 2 ? for iec - 320 - c8 type, ? 3 ? for iec - 320- c6 , or ? 6 ? for iec - 320- c18 type. 2. the output voltage is specified as a range (ex: 36~48 vdc); the custo mer must specify what they want the voltage set at. 3. line regulation is defined by changing 10% of input voltage from nominal line at rated load. 4. ripple and noise is measured at nominal line and full load with 20mhz bandwidth and a 0.1f ceramic ca pacit or and 47f aluminum capacitors in parallel across the output. 5 . led option available. 6 . optional output connectors are available. please call factory for ordering details.
rev b dtem 1024 series 16~36 watts medical ac/dc desktop power supplies 09/22 /201 4 wall industries, inc. ? 37 industrial drive, exeter, nh 03833 ? tel: 603 - 778 - 2300 ? toll free: 888 - 597 - 9255 ? fax 603 - 778 - 9797 website: www.wallindustries.com ? e - mail: sales@wallindustries.com page 2 of 3 technical specifications: DTEM1024 series all specifications are base d on 25c, nominal input voltage, and maximum output current unless otherwise noted. we reserve the right to change specifications based on technological advances. specification test conditions min typ max unit input specifications input voltage 100 2 40 vac input frequency 50 60 hz input current 0.5 1 a inrush current cold start 60 a output specifications output voltage see table line regulation defined by changing 10% of input voltage from nominal line at rated load -1 +1 % load regula tion -5 +5 % output power see table output current see table minimum load 0 a ripple & noise (20mhz bw) measured at nominal line and full load with 0.1f ceramic and 47f aluminum capacitors in parallel see table hold - up time 8.3 ms turn -on time 3 s protection over voltage protection automatic recovery short circuit protection automatic recovery general specifications efficiency meet cec level v, vi environmental specifications operating temperature 0 +40 c storage temperat ure -20 +85 c operating humidity 10 9 0 % storage humidity 5 95 % cooling free air convection mtbf 30,000 hours physical specifications weight 7.05oz (200 g) dimensions (l x w x h) 3.94 x 1.77 x 1.22 inches (100 x 45 x 31 mm) ac inlet co nnector suffix ?1? iec - 320 - c14 suffix ?2? iec - 320 - c8 suffix ?3? iec - 320 - c6 suffix ?6? iec - 320 - c18 output connectors c all factory for ordering details several options available safety & compliance safety approvals ul/cul ul 60601: 3 rd edition for class ii only tuv/sud en/iec 60601 - 1: 3rd edition cb, ce, and fcc compliance rohs, weee, cec level v, vi
rev b dtem 1024 series 16~36 watts medical ac/dc desktop power supplies 09/22 /201 4 wall industries, inc. ? 37 industrial drive, exeter, nh 03833 ? tel: 603 - 778 - 2300 ? toll free: 888 - 597 - 9255 ? fax 603 - 778 - 9797 website: www.wallindustries.com ? e - mail: sales@wallindustries.com page 3 of 3 mechanical drawing company information wall industries, inc. has created custom and modified units for over 50 years. our in - house research and development engineers will provide a solution that exceeds your performance requirements on - time and on budget. our iso9001 - 2008 certification is just one example of our commitment to producing a high quality, well - docum ented product for our customers. our past projects demonstrate our commitment to you, our customer. wall industries, inc. has a reputation for working closely with its customers to ensure each solution meets or exceeds form, fit and function requirements. we will continue to provide ongoing support for your project above and beyond the design and production phases. give us a call today to discuss your future projects. contact wall industries for further information: phone: ? (603)778- 2300 toll free: ? (88 8)5 9 7 - 9255 fax: ? (603)778- 9797 e - mail: sales@wallindustries.com web: www.wallindustries.com address: 37 industrial drive exeter, nh 03833
|
